收藏本站
LT3746
PIN FUNCTIONS
EN/UVLO (Pin 1): Enable and Undervoltage Lockout
(UVLO) Pin. The pin can accept a digital input signal to
enable or disable the chip. Tie to 0.35V or lower to shut
down the chip or tie to 1.34V or higher for normal operation.
This pin can also be connected to V IN through a resistor
divider to program a power input UVLO threshold. If both
the enable and UVLO functions are not used, tie this pin
to V CC pin.
LED00 to LED31 (Pins 2-17, 30-45): LED Driver Output
Pins. Connect the cathodes of LED strings to these pins.
GND (Pin 18, 20, 27, 29): Ground Pin.
SCKI (Pin 19): Serial Interface TTL/CMOS Logic Clock
Input Pin.
SDI (Pin 21): Serial Interface TTL/CMOS Logic Data
Input Pin.
LDI (Pin 22): Serial Interface TTL/CMOS Logic Latch Input
Pin. An asynchronous input signal at this pin latches the
serial data in the shift registers into the proper registers
and the status information is ready to shift out with the
coming clock pulses. See more details in the Operation
section.
V CC (Pin 23): Logic and Control Supply Pin. The pin powers
serial data interface and internal control circuitry. Must be
locally bypassed with a capacitor to ground.
PWMCK (Pin 24): Grayscale PWM Dimming TTL/CMOS
Logic Clock Pin. Individual PWM dimming signal is gener-
ated by counting this clock pulse from zero to the bits in
its 12-bit grayscale PWM register.
LDO (Pin 25): Serial Interface TTL/CMOS Logic Latch
Output Pin.
SDO (Pin 26): Serial Interface TTL/CMOS Logic Data
Output Pin.
SCKO (Pin 28): Serial Interface TTL/CMOS Logic Clock
Output Pin.
SYNC (Pin 46): Switching Frequency Synchronization
Pin. Synchronizes the internal oscillator frequency to an
external clock applied to the SYNC pin. The SYNC pin is
TTL/CMOS logic compatible. Tie to ground or V CC if not
used.
RT (Pin 47): Timing Resistor Pin. Programs the switching
frequency from 200kHz to 1MHz. See Table 2 for the rec-
ommended R T values for common switching frequencies.
SS (Pin 48): Soft Start Pin. Placing a capacitor here pro-
grams soft start timing to limit inductor inrush current
during startup. The soft start cycle will not begin until all
the V CC , EN/UVLO, and (V IN - V CAP ) voltages are higher
than their respective UVLO thresholds.
FB (Pin 49): Feedback Pin. The pin is regulated to the
internal band-gap reference 1.205V during startup and
precharging phases. Connect to a resistor divider from
the buck converter output to program the maximum LED
bus voltage. See more details in the Applications Informa-
tion section.
ISN (Pin 50): Negative Inductor Current Sense Pin. The
pin is connected to one terminal of the external inductor
current sensing resistor and the buck converter output
supplying parallel LED channels.
ISP (Pin 51): Positive Inductor Current Sense Pin. The pin
is connected to the inductor and the other terminal of the
external inductor current sensing resistor.
CAP (Pin 52): V IN Referenced Regulator Supply Capacitor
Pin. The pin holds the negative terminal of an internal V IN
referenced 6.8V linear regulator used to bias the gate driver
circuitry. Must be locally bypassed with a capacitor to V IN .
GATE (Pin 53): Gate Driver Pin. The pin drives an external
P-channel power MOSFET with a typical peak current of 1A.
Connect this pin to the gate of the power MOSFET with a
short and wide PCB trace to minimize trace inductance.
V IN (Pin 54): Power Input Supply Pin. Must be locally
bypassed with a capacitor to ground.
T SET (Pin 55): Temperature Threshold Setting Pin. A
resistor to ground programs overtemperature threshold.
See more details in the Applications Information section.
I SET (Pin 56): Nominal LED Current Setting Pin. A resistor
to ground programs the nominal LED current for all the
channels. See more details in the Applications Informa-
tion section.
Exposed Pad (Pin 57): Ground Pin. Must be soldered to a
continuous copper ground plane to reduce die temperature
and to increase the power capability of the device.
For more information www.linear.com/3746
3746fa
11
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
LT3754IUH#TRPBF IC LED DVR 16CH 50MA 32QFN
LT3755EMSE#PBF IC LED DRVR HP CONS CURR 16-MSOP
LT3760EFE#PBF IC LED DVR WHT/CLR BCKLT 28TSSOP
LT3799IMSE#PBF IC LED DRIVER TRIAC DIM 16-MSOP
LT3956EUHE#PBF IC LED DVR BUCK BOOST 36-VQFN
LTC3201EMS#TRPBF IC LED DRVR WHITE BCKLGT 10-MSOP
LTC3202EDD#PBF IC LED DRIVR WHITE BCKLGT 10-DFN
LTC3205EUF#TRPBF IC LED DRVR WT/RGB BCKLGT 24-QFN
相关代理商/技术参数
LT3748 制造商:LINER 制造商全称:Linear Technology 功能描述:Monolithic High Voltage Isolated Flyback Converter No External Start-Up Resistor
LT3748_1 制造商:LINER 制造商全称:Linear Technology 功能描述:100V Isolated Flyback Controller
LT3748EMS#PBF 功能描述:IC REG CTRLR FLYBK ISO CM 16MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX
LT3748EMS#TRPBF 功能描述:IC REG CTRLR FLYBK ISO CM 16MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR)
LT3748EMSPBF 制造商:Linear Technology 功能描述:100V Isolated Flyback Controller MSOP16
LT3748EMSTRPBF 制造商:LINER 制造商全称:Linear Technology 功能描述:100V Isolated Flyback Controller
LT3748HMS#PBF 功能描述:IC REG CTRLR FLYBK ISO CM 16MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 特色产品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 标准包装:1 系列:PowerWise® PWM 型:电压模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.5 V ~ 18 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-5°C ~ 125°C 封装/外壳:32-WFQFN 裸露焊盘 包装:Digi-Reel® 产品目录页面:1303 (CN2011-ZH PDF) 其它名称:LM3754SQDKR
LT3748HMS#TRPBF 功能描述:IC REG CTRLR FLYBK ISO CM 16MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX